|
Please see below for specifications on edge
profiles, stoves,
faucets and sinks.
EDGE PROFILES:
 |
 |
 |
 |
| Eased Edge |
Micro Bevel |
Half Bevel |
Demi Bullnose |
 |
 |
 |
 |
| Half Bullnose |
Full Bullnose |
Ogee - Upgrade |
Dupont - Upgrade |
STOVES - WHAT YOU NEED TO KNOW:
FREESTANDING
A freestanding stove is a stove that easily slides into an
opening usually between two cabinets or at the end of a
cabinet run. The dials are most likely located on a panel
at the back of the stove which takes the place of a traditional
4” granite backsplash.
When using this type of stove there is little we need to
know beyond the placement of the stove. We minimize the overhang
on the cabinet next to the stove and flat polish the edges
to assure a tight fit.
SLIDE-IN
A slide-in stove is a stove that also slides into an opening
between two cabinets and usually lips the countertop on
both sides. This stove, however, usually has dials located
on the front face plate of the stove and does not have
the back riser like a freestanding.
When using this type of stove, we will need to know if you
require a granite strip to run behind the stove. Some models
come with a strip and others do not. Be sure to read your
instruction manual to verify that a granite strip is compatible
with your stove. The granite strip is usually about 2” by
30” and is seamed to the stone on either side of your stove.
COOKTOP
A cooktop is a stove comprised of only the top burners. This
type of stove sits directly on top of your countertop and
has dials located on its surface. The oven can be directly
beneath it or located in an entirely different place.
When using this type of stove, you first need to verify
that the stove will fit into your cabinet space. Then, we
will need to have the appliance on sight at the time of install.
Cooktop cutouts are cut on sight to assure correct measurements.
FAUCETS - WHAT YOU NEED TO KNOW:
The main concern with a faucet is the number of holes it
has. We need to know how many holes you want drilled as well
as where you would like them placed. A faucet is generally
centered at the sink; however, other holes such as the soap
dispenser, sprayer and air switch are not “standard”.
If you choose an undermount sink, you want to be sure to
buy a faucet that does not have an escutcheon plate.
SINKS - WHAT YOU NEED TO KNOW:
When choosing a sink, there are several things to consider.
The bowl size and configuration, depth, material and the
faucet are a few factors.
The bowl size is important in that you must make sure the
sink will fit into your cabinet with room for faucet holes
behind it. Configuration refers to the option of having one
bowl, two bowls the same size, two bowls of a different size
or many other options. The depth of a sink can vary greatly
and should be considered when purchasing a sink. Remember,
when using an undermount sink, the sink will be attached
beneath the countertop and another inch will be added to
the depth. The material is more a personal preference but
there are several options, including; stainless steel, porcelain
and silgranit. Finally, the faucet should be considered for
reasons described above.
DROP-IN
A drop-in sink is one that sits directly on top of the counter.
The faucet comes in one piece connected by an escutcheon
plate. There are a number of ways your sink can be attached
to the countertop depending upon your particular sink.
The attachment is handled by your plumber.
When using a drop-in sink, the sink must be on site at the
time of install. The hole is generally cut on site.
UNDERMOUNT
An undermount sink is one that attaches to the countertop from underneath.
The sink is generally secured to the stone with silicone and a wooden cradle
that is attached to the frame of the cabinet.
When using an undermount sink, we must have the physical
sink or the approved template before we begin fabricating
your piece. The sink opening is cut and polished prior to
the installation. Faucet holes are still drilled on site.
Please see the undermount
sink brochure for more information.
FARM SINK
A farm sink, or an apron front sink, sits on a support structure
below the cabinets. The face of the sink is exposed and
the top of the sink is generally level with the top of
the cabinets.
When using a farm sink, the sink must be set in place before
we come to measure for the countertops. Your cabinet installer
or GC should be able to do this for you. After we measure,
the sink should not be moved. We take measurements not only
of the stone that sits beside the sink but also its placement
within the cabinet front to back. Faucet holes are still
drilled on site.
If you have any questions or would like more information,
please contact Heritage Stone.
|
